Meidling Concrete, Inc. "Our reputation is concrete™."

Wall Systems Specifications

Pattern: #90500 12" CUT STONE

STONE-CRETE

Stone-Crete is a deep relief form liner system that incorporates a patented process to achieve natural stone configurations out of concrete. The following are design considerations when specifying Stone-Crete on a project. Also, refer to the Spec Aid/ Stone-Crete, Patent Summary and Installation Instructions for other information on the design and specifications of this system.

Section I - FORM WORK

Type: Job Site Built Hand Set Gang

Panel Face: Plywood Aluminum Steel

Ties: Fiberglass, Steel

Release: Increte Form Liner Release, Non-Staining Agent

Section II - FORM LINER*

Composition: Urethane Rubber/Urethane Foam

Rotation: 180 Degrees

Keying: Removable

Attachment: Bolts, Self Tapping Screws

Thickness: 0’ – 2 3/8"

Relief: 0’ - 2"

Form Size: 2’-0" x 6’-0" (2)

Filler Sizes: None

Corner Size: Out - 1’-6" x 6’-0" (Qoined), Out - 2’-0" x 2’-0" (Mitered)

Rock Sizes: 14" to 30"

Section III - CONCRETE

Placement: Traditional Methods and Vibration

Reinforcement: ACI and Local Building Code Specifications

Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained

Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching)

Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal

Section IV – DESIGN CONSIDERATIONS

When designing for the use of Stone-Crete form liners keep the following in mind:

- Add the liner thickness to the reinforcement coverage.
- Curved walls can be achieved down to a 10’-0" radius (Rubber).
- The concrete must cure a minimum of two weeks before applying Stain-Crete.
- The form liners can be gang formed and used to precast.

*Note: See accessory and pricing sheets for additional sizes.

(800) 752-4626 Pattern: #90300 24" CUT STONE

STONE-CRETE

Section I - FORM WORK

Type: Job Site Built, Hand Set, Gang

Panel Face: Plywood, Aluminum, Steel

Ties: Fiberglass, Steel

Release: Increte Form Liner Release Non-Staining Agent

Section II - FORM LINER *

Composition: Urethane Rubber/Urethane Foam

Rotation: 180 Degrees

Keying: None

Attachment: Bolts, Self Tapping Screws

Thickness: 0’ – 4 1/4"

Relief: 0’ - 4"

Form Size: 4’-0" x 2’-0" (2)

Filler Sizes: 6’-0" x 2’-0"

3’-0" x 2’-0" (2)

2’-0" x 2’-0"

Corner Size: Out - 1’-6" x 6’-0" (Qoined)

Rock Sizes: 2’-0" to 6’-0"

Section III - CONCRETE

Placement: Traditional Methods and Vibration

Reinforcement: ACI and Local Building Code Specifications

Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained

Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching)

Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal

Section IV – DESIGN CONSIDERATIONS

When designing for the use of Stone-Crete form liners keep the following in mind:

- Add the liner thickness to the reinforcement coverage.
- Curved walls can be achieved down to a 10’-0" radius.
- The concrete must cure a minimum of two weeks before applying Stain-Crete.
- The form liners can be gang formed and used to precast.

*Note: See accessory and pricing sheets for additional sizes.

Pattern: #90100

DRY STACKSTONE-CRETE

Section I - FORM WORK

Type: Job Site Built Hand Set Gang

Panel Face: Plywood Aluminum Steel

Ties: Fiberglass Steel

Release: Increte Form Liner Release Non-Staining Agent

Section II - FORM LINER *

Composition: Urethane Rubber/Urethane Foam

Rotation: 180 Degrees

Keying: Vertical

Attachment: Bolts, Self Tapping Screws

Thickness: 0’ – 1 3/4"

Relief: 0’ – 1 3/8"

Form Size: 6’-0" x 2’-0" (2)

Filler Sizes: 4’-0" x 2’-0", 2’-0" x 2’-0"

Corner Size: Out - 1’-0" x 6’-0"

Rock Sizes: 2" to 16"

Section III - CONCRETE

Placement: Traditional Methods and Vibration

Reinforcement: ACI and Local Building Code Specifications

Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained

Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching)

Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal

Section IV – DESIGN CONSIDERATIONS

When designing for the use of Stone-Crete form liners keep the following in mind:

*Note: See accessory and pricing sheets for additional sizes.

(800) 752-4626 Pattern: #90200 SEDONA

STONE-CRETE

Section I - FORM WORK

Type: Job Site Built, Hand Set, Gang

Panel Face: Plywood, Aluminum, Steel

Ties: Fiberglass Steel

Release: Increte Form Liner Release, Non-Staining Agent

Section II - FORM LINER *

Composition: Urethane Rubber/Urethane Foam

Rotation: 180 Degrees

Keying: Removable

Attachment: Bolts, Self Tapping Screws

Thickness: 0’ – 2 3/8"

Relief: 0’ - 2"

Form Size: Horz. - 6’-0" x 2’-0" (2) Vert. - 2’-0" x 6’-0"

Filler Sizes: 4’-0" x 2’-0" 0’-6" x 6’-0"

6’-0" x 0’-8" 0’-8" x 6’-0"

0’-1" x 6’-0" 0’-10" x 6’-0"

0’-2" x 6’-0" 1’-0" x 6’-0"

0’-4" x 6’-0"

Corner Size: Out - 1’-0" x 6’-0" In – 0’-4" x 6’-0"

Rock Sizes: 4" to 35"

Section III - CONCRETE

Placement: Traditional Methods and Vibration

Reinforcement: ACI and Local Building Code Specifications

Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained

Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching)

Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal

Section IV – DESIGN CONSIDERATIONS

When designing for the use of Stone-Crete form liners keep the following in mind:

*Note: See accessory and pricing sheets for additional sizes.

MeidlingConcrete.com \| 509-924-7180

	Home Decorative Commercial HTP Flooring Wall Systems Gallery Specifications Projects Gallery Counter Tops Polishing Display Area's About Us Contact Us	Wall Systems Specifications Pattern: #90500 12" CUT STONE STONE-CRETE Stone-Crete is a deep relief form liner system that incorporates a patented process to achieve natural stone configurations out of concrete. The following are design considerations when specifying Stone-Crete on a project. Also, refer to the Spec Aid/ Stone-Crete, Patent Summary and Installation Instructions for other information on the design and specifications of this system. Section I - FORM WORK Type: Job Site Built Hand Set Gang Panel Face: Plywood Aluminum Steel Ties: Fiberglass, Steel Release: Increte Form Liner Release, Non-Staining Agent Section II - FORM LINER* Composition: Urethane Rubber/Urethane Foam Rotation: 180 Degrees Keying: Removable Attachment: Bolts, Self Tapping Screws Thickness: 0’ – 2 3/8" Relief: 0’ - 2" Form Size: 2’-0" x 6’-0" (2) Filler Sizes: None Corner Size: Out - 1’-6" x 6’-0" (Qoined), Out - 2’-0" x 2’-0" (Mitered) Rock Sizes: 14" to 30" Section III - CONCRETE Placement: Traditional Methods and Vibration Reinforcement: ACI and Local Building Code Specifications Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching) Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal Section IV – DESIGN CONSIDERATIONS When designing for the use of Stone-Crete form liners keep the following in mind: - Add the liner thickness to the reinforcement coverage. - Curved walls can be achieved down to a 10’-0" radius (Rubber). - The concrete must cure a minimum of two weeks before applying Stain-Crete. - The form liners can be gang formed and used to precast. Note: See accessory and pricing sheets for additional sizes. (800) 752-4626 Pattern: #90300 24" CUT STONE STONE-CRETE Stone-Crete is a deep relief form liner system that incorporates a patented process to achieve natural stone configurations out of concrete. The following are design considerations when specifying Stone-Crete on a project. Also, refer to the Spec Aid/ Stone-Crete, Patent Summary and Installation Instructions for other information on the design and specifications of this system. Section I - FORM WORK* Type: Job Site Built, Hand Set, Gang Panel Face: Plywood, Aluminum, Steel Ties: Fiberglass, Steel Release: Increte Form Liner Release Non-Staining Agent Section II - FORM LINER * Composition: Urethane Rubber/Urethane Foam Rotation: 180 Degrees Keying: None Attachment: Bolts, Self Tapping Screws Thickness: 0’ – 4 1/4" Relief: 0’ - 4" Form Size: 4’-0" x 2’-0" (2) Filler Sizes: 6’-0" x 2’-0" 3’-0" x 2’-0" (2) 2’-0" x 2’-0" Corner Size: Out - 1’-6" x 6’-0" (Qoined) Rock Sizes: 2’-0" to 6’-0" Section III - CONCRETE Placement: Traditional Methods and Vibration Reinforcement: ACI and Local Building Code Specifications Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching) Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal Section IV – DESIGN CONSIDERATIONS When designing for the use of Stone-Crete form liners keep the following in mind: - Add the liner thickness to the reinforcement coverage. - Curved walls can be achieved down to a 10’-0" radius. - The concrete must cure a minimum of two weeks before applying Stain-Crete. - The form liners can be gang formed and used to precast. Note: See accessory and pricing sheets for additional sizes. Pattern: #90100* DRY STACKSTONE-CRETE Stone-Crete is a deep relief form liner system that incorporates a patented process to achieve natural stone configurations out of concrete. The following are design considerations when specifying Stone-Crete on a project. Also, refer to the Spec Aid/ Stone-Crete, Patent Summary and Installation Instructions for other information on the design and specifications of this system. Section I - FORM WORK Type: Job Site Built Hand Set Gang Panel Face: Plywood Aluminum Steel Ties: Fiberglass Steel Release: Increte Form Liner Release Non-Staining Agent Section II - FORM LINER * Composition: Urethane Rubber/Urethane Foam Rotation: 180 Degrees Keying: Vertical Attachment: Bolts, Self Tapping Screws Thickness: 0’ – 1 3/4" Relief: 0’ – 1 3/8" Form Size: 6’-0" x 2’-0" (2) Filler Sizes: 4’-0" x 2’-0", 2’-0" x 2’-0" Corner Size: Out - 1’-0" x 6’-0" Rock Sizes: 2" to 16" Section III - CONCRETE Placement: Traditional Methods and Vibration Reinforcement: ACI and Local Building Code Specifications Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching) Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal Section IV – DESIGN CONSIDERATIONS When designing for the use of Stone-Crete form liners keep the following in mind: - Add the liner thickness to the reinforcement coverage. - Curved walls can be achieved down to a 10’-0" radius (Rubber). - The concrete must cure a minimum of two weeks before applying Stain-Crete. - The form liners can be gang formed and used to precast. Note: See accessory and pricing sheets for additional sizes. (800) 752-4626 Pattern: #90200 SEDONA STONE-CRETE Stone-Crete is a deep relief form liner system that incorporates a patented process to achieve natural stone configurations out of concrete. The following are design considerations when specifying Stone-Crete on a project. Also, refer to the Spec Aid/ Stone-Crete, Patent Summary and Installation Instructions for other information on the design and specifications of this system. Section I - FORM WORK* Type: Job Site Built, Hand Set, Gang Panel Face: Plywood, Aluminum, Steel Ties: Fiberglass Steel Release: Increte Form Liner Release, Non-Staining Agent Section II - FORM LINER * Composition: Urethane Rubber/Urethane Foam Rotation: 180 Degrees Keying: Removable Attachment: Bolts, Self Tapping Screws Thickness: 0’ – 2 3/8" Relief: 0’ - 2" Form Size: Horz. - 6’-0" x 2’-0" (2) Vert. - 2’-0" x 6’-0" Filler Sizes: 4’-0" x 2’-0" 0’-6" x 6’-0" 6’-0" x 0’-8" 0’-8" x 6’-0" 0’-1" x 6’-0" 0’-10" x 6’-0" 0’-2" x 6’-0" 1’-0" x 6’-0" 0’-4" x 6’-0" Corner Size: Out - 1’-0" x 6’-0" In – 0’-4" x 6’-0" Rock Sizes: 4" to 35" Section III - CONCRETE Placement: Traditional Methods and Vibration Reinforcement: ACI and Local Building Code Specifications Composition: 3500 psi (min), ½" +/- ¼" Stone, Air Entrained Color: Color-Crete Integral Color (30 Standard Colors plus Custom Matching) Finish: Stain-Crete Chemical Staining, Color Spray, Increte Acrylic Clear Seal Section IV – DESIGN CONSIDERATIONS When designing for the use of Stone-Crete form liners keep the following in mind: - Add the liner thickness to the reinforcement coverage. - Curved walls can be achieved down to a 10’-0" radius (Rubber). - The concrete must cure a minimum of two weeks before applying Stain-Crete. - The form liners can be gang formed and used to precast. *Note: See accessory and pricing sheets for additional sizes.
© 2007 Meidling Concrete, Inc. FBSite © 2007 1st Byte Solutions - Version 0.6.10 - Login Document last updated: November 27 2007 20:33:17